Accessories For SL50 Series Data Loggers - Signatrol UK

SL50-ACC01

316 stainless steel enclosures that protect the SL50 series data loggers in harsh environments or where there is likely to pressures in excess of 100mB. The SL50-ACC01 can be used with pressures up to 10 Bar or submerged in up to 100m water.

Diameter Ø25.0mm, Height 18.5mm, widest part of the hex nut is 29.0mm.

Weight: 40g excluding data logger

Download Datasheet

SL50-ACC03

A lower cost alternative to the SL-ACC01. The
SL-ACC03 is constructed from Polyphenylene Sulphide (PPS Ryton) with black flat finish. This produces a lightweight enclosure that protects the data logger at pressures up to 1 Bar or depths of 10m. Maximum operating temperature +125°C.

Diameter Ø25.4mm, Height 28.0mm

Weight: 15g excluding data logger

Click here for mechanical drawing

Download Datasheet

SL50-ACC06

The lowest cost waterproof enclosure for the SL50 series data loggers. The SL-ACC06 is constructed from neutral coloured silicone. This produces a lightweight, two part enclosure that protects the data logger at pressures up to 0.5 Bar or depths of 5m. The maximum operating temperature is well in excess of the +125°C maximum operating temperature of the SL53T.

The enclosure may be reused many times but the actual number of times depends upon many factors such as the temperature, the liquid type , the duration. Each time before use carefully inspect the cap for signs of damage and if in doubt discard.

Diameter Ø22.5mm, Length 25.0mm

Weight: 5g excluding data logger

Download Instruction Sheet

Download Datasheet

Sold in packs of 5 or 10

SL50-ACC02

If there are any downsides to the SL50 series data loggers, it could be argued that for some applications they are just too small! For this type of application, we provide the SL50-ACC02 rubberised holder. Any member of the SL50 family just clips into the bright yellow holder and is held securely. There is a mounting hole for fixing the holder in place as well as a strong magnet mounted on the back of the holder.

Length 63mm, Width 56mm, Height 8mm.

SL50-CLIP

The SL50-CLIP is a small black, plastic key fob that will accept any of the SL50 series data loggers. Each logger just pushes into the clip and the mounting eye provides a convenient way of securing the clip. Operating temperature range 0°C to +70°C

Supplied in packs of five.

SL50-WALL

A black plastic, wall mounting bracket that allows any of the SL50 series data loggers to be permanently fixed to a wall, door or even a packing crate. The SL50 series loggers protrude through the enclosure which is in turn fixed using two screws.

Supplied in packs of five.

SL50-ACC07

The SL50-ACC07 is an alarm viewer for all SL50 series data loggers. Just place the data logger in the socket and press the button. A green lamp will illuminate if the alarms have not been triggered and a red light will illuminate if they have.

SL50-ACC08

A coloured waterproof enclosure which is slightly larger than the SL50-ACC06. Being blue and yellow, the SL50-ACC08 is easier to spot when mixed with product. And the blue handle makes the bung easier to remove. Please note, unlike the SL50-ACC06, the SL50-ACC08 floats in fluid.

The enclosure may be reused many times but the actual number of times depends upon many factors such as the temperature, the liquid type , the duration. Each time before use carefully inspect the cap for signs of damage and if in doubt discard.

Diameter Ø21.6mm, Length 55.0mm

Supplied in packs of five or ten

SL50-ACC09

The SL50-ACC09 is a battery powered handheld printer that can be used to print reports from the SL51T, SL52T, SL53T and SL54TH data loggers.

The report generated shows the data logger serial number, when the data logger started and stopped logging. It also indicates the preprogrammed alarm limits and if these limits have been exceeded.

The SL50-ACC09 is ideal for producing reports when temperature sensitive goods are handed over or delivered.

The handheld printer is supplied with rechargable batteries and charger.